View CS61581_257098.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CS61581 CS61581
T1/E1 Universal Line Interface
Features
T1 and E1, Long Haul and Short Haul Line Interface l Provides a QRSS Test Signal and Error Detector l Impedance Matching Line Driver Using a Single Transformer l Greater than 14 dB of Transmit Return Loss Without Using External Resistors l No Crystal Needed for Jitter Attenuation l Meets AT&T 62411 and TBR 12/13 Jitter Tolerance and Attenuation Requirements l Meets ANSI T1.231B and ITU-T G.775 Requirements for LOS and AIS l Meets the BS6450 Transmitter Short-Circuit Requirements for E1 Applications l Compliant with:
- ITU-T Recommendations: G.703, G.732, G.775 and I.431 - American National Standards (ANSI): T1.102, T1.105, T1.403, T1.408, and T1.231
l Provides
- FCC Rules and Regulations: Part 68 and Part 15 - AT&T Publication 62411 - ETSI ETS 300 011, 300 233, TBR 12/13 - TR-NET-00499
Description
The CS61581 is a primary rate line interface unit capable of operation in both short haul (intraoffice) and long haul applications. The CS61581 combines the complete analog transmit and receive circuitry for a single, full-duplex interface at T1 and E1 rates. The device is pin and function compatible with the Level One LXT310 and LXT318 (the latter in the host mode only). The device can also replace LXT359 and LXT360. Enhanced functionality is available through an extended register set allowing short haul operation, custom pulse shape generation, QRSS pattern generation, detection and error counting, and generation and detection of loop up and loop down codes. The CS61581 features Crystal(R) low-power impedance-matched line drivers and crystalless jitter attenuation. ORDERING INFORMATION CS61581-IL 28-pin PLCC CS61581-IP 28-pin PDIP
TCLK TDATA/TPOS UBS/TNEG JASEL
2
3
4 11
E N C O D E R
JITTER ATTEN
TRANSMIT TIMING & CONTROL
PULSE SHAPING CIRCUITRY ROM / RAM
13
LINE DRIVERS
TTIP
16 28 26 27 24 25
TRING CLKE/TAOS CS/RLOOP SCLK/LLOOP SDI/LBO1 SDO/LBO2
TAOS Enable Q R S S REMOTE LOOPBACK LOCAL LOOPBACK (DIGITAL)
LBO Select
SERIAL PORT
REGISTERS & CONTROL LOGIC LOS/ NLOOP Clear LLOOP Enable LOCAL LOOPBACK (ANALOG) SH NOISE & CROSSTALK FILTERS SH MAGNITUDE EQUALIZER
SH/LH EQUALIZER CONTROL SLICERS & PEAK DETECT
RCLK RDATA/RPOS
BPV/RNEG
D 8E C 7O D 6 E R
18
JITTER ATTEN
TIMING & DATA RECOVERY
LATN
AGC
19 20
RTIP
RRING
INT/NLOOP LOS
23 12
INBAND NLOOP & LOS PROCESSOR
RECEIVE CLOCK GENERATOR
1
MCLK
9 XTALIN
10 XTALOUT
5 MODE
21 RV+
22
14
15 TV+
RGND TGND
Preliminary Product Information
P.O. Box 17847, Austin, http://www.cirrus.com Texas 78760 (512) 445 7222 FAX: (512) 445 7581 http://www.cirrus.com
This document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice.
Copyright . Cirrus Copyright (c) Cirrus Logic, Inc. 2005 Logic, Inc. 2000 (All Rights Reserved) (All Rights Reserved)
DS211PP8 AUG `05 APR `00 DS211F1 1
CS61581
T A B L E OF C ONT E NT S
1. CHARACTERISTICS AND SPECIFICATIONS ..................................................................4 ABSOLUTE MAXIMUM RATINGS .....................................................................4 RECOMMENDED OPERATING CONDITIONS .................................................4 DIGITAL CHARACTERISTICS...........................................................................4 ANALOG SPECIFICATIONS..............................................................................5 T1 SWITCHING CHARACTERISTICS ...............................................................7 E1 SWITCHING CHARACTERISTICS...............................................................7 SWITCHING CHARACTERISTICS ....................................................................9 2. THEORY OF OPERATION ...............................................................................................10 2.1 Operating Mode Selection ........................................................................10 2.2 Master Clocks ...........................................................................................10 2.3 Transmitter ................................................................................................10 2.4 Transmit All Ones Select ..........................................................................12 2.4.1 Receiver ..........................................................................................13 2.4.2 Short Haul .......................................................................................13 2.4.3 Long Haul ........................................................................................13 2.4.4 Clock Recovery ...............................................................................13 2.4.5 Jitter Tolerance ...............................................................................14 2.5 Receiver Line Attenuation Indication ........................................................14 2.6 Jitter Attenuator ........................................................................................14 2.7 Receiver Loss of Signal ............................................................................14 2.8 Local Loopback ........................................................................................15 2.9 Remote Loopback .....................................................................................16 2.10 Network Loopback ..................................................................................16 2.11 Alarm Indication Signal ...........................................................................16 2.12 Serial Interface .......................................................................................16 2.21 Interrupts ................................................................................................23 3. QRSS TEST MODE ..........................................................................................................23 4. ARBITRARY WAVEFORM GENERATION ......................................................................24 4.1 Power On Reset / Reset ...........................................................................25 4.2 Power Supply ............................................................................................26 6. PIN DESCRIPTION ...........................................................................................................31 6.1 Power Supplies .........................................................................................32 6.2 Oscillator ...................................................................................................32 6.3 Control ......................................................................................................32 6.4 Status .......................................................................................................33 6.5 Serial Control Interface .............................................................................33 6.6 Data Input/Output .....................................................................................34 7. PACKAGE DIMENSIONS ................................................................................................36
2
DS211F1 DS211PP8
CS61581
LIST OF FIGURES
Figure 1. Signal Rise and Fall Characteristics ............................................................................... 8 Figure 2. Recovered Clock and Data Switching Characteristics.................................................... 8 Figure 3. Transmit Clock and Data Switching Characteristics ....................................................... 8 Figure 4. Serial Port Write Timing Diagram ................................................................................... 9 Figure 5. Serial Port Read Timing Diagram ................................................................................... 9 Figure 6. Typical Pulse Shape at DSX-1 Cross Connect............................................................. 12 Figure 7. Mask of the Pulse at the 2048 kbps Interface............................................................... 12 Figure 8. Minimum Input Jitter Tolerance of Receiver ................................................................. 13 Figure 9. LATN Pulse Width encoding ......................................................................................... 14 Figure 10.Typical Jitter Transfer Function - T1 ............................................................................. 15 Figure 11.Typical Jitter Transfer Function - E1 ............................................................................. 15 Figure 12.Input/Output Timing (showing address 0x10) ............................................................... 17 Figure 13.Phase Definition of Arbitrary Waveforms ...................................................................... 24 Figure 14.Example of Summing of Waveforms............................................................................. 25 Figure 15.Matched Impedance Output Configuration ................................................................... 28 Figure 16.Low Impedance Output Configuration .......................................................................... 29 Figure 17.Typical System Connection .......................................................................................... 30
LIST OF TABLES
Table 1. Pulse Shape Selection and Transformer Requirements ................................................. 11 Table 2. Data Output/Clock Relationship ...................................................................................... 13 Table 3. Register Map................................................................................................................... 17 Table 4. Register 0x10 Decoding.................................................................................................. 23 Table 5. Register 0x10 Decoding.................................................................................................. 23 Table 5. Diagnostic Mode Availability ........................................................................................... 26 Table 6. Transformer Specification ............................................................................................... 26 Table 7. Recommended Transformers for the CS61581 .............................................................. 27
DS211F1 DS211PP8
3
CS61581
1. CHARACTERISTICS AND SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Parameter DC Supply Input Voltage, Any Pin Input Current, Any Pin Ambient Operating Temperature Storage Temperature (Note 1) (referenced to RGND=TGND=0 V) Symbol RV+ TV+ Vin Iin TA Tstg Min RGND-0.3 -10 -40 -65 Max 6.0 (RV+) + 0.3 (RV+) + 0.3 10 85 150 Units V V V mA
C C
WARNING: Operations at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes Notes: 1 Transient currents of up to 100 mA will not cause SCR latch-up. Also TTIP, TRING, TV+ and TGND can withstand a continuous current of 100 mA.
RECOMMENDED OPERATING CONDITIONS
Parameter DC Supply Ambient Operating Temperature Power Consumption, Long Haul Symbol (Note 1) RV+, TV+ TA (Notes 2,3,4) PC Low Z Match Z (Notes 2,3,4) PC Low Z Match Z Min 4.75 -40 Typ 5.0 25 390 400 480 430 Max 5.25 85 630 575 725 650 Units V C mW
Power Consumption, Short Haul
mW
Notes: 1. TV+ must not exceed RV+ by more than 0.3 V. 2. Power consumption while driving line load over operating temperature range. Includes IC and load. Digital input levels are within 10% of the supply rails and digital outputs are driving a 50 pF capacitive load. 3. Typical consumption corresponds to 50% ones density and medium line length at 5.0 V. 4. Maximum consumption corresponds to 100% ones density and maximum line length at 5.25 V.
DIGITAL CHARACTERISTICS (TA = -40C to 85C; TV+, RV+ = 5.0 V 5%; GND = 0 V)
Parameter High-Level Input Voltage Low-Level Input Voltage High-Level Output Voltage IOUT = -40 A Low-Level Output Voltage IOUT = 1.6 mA Input Leakage Current (Note 5) PINS 1-4, 24-28 (Note 5) PINS 1-4, 24-28 (Notes 5, 6) PINS 6-8, 25 (Notes 5, 6) PINS 6-8, 25 Symbol VIH VIL VOH VOL Min 2.0 2.4 Typ Max 0.8 0.4
10
Units V V V V
A
Notes: 5. This specification guarantees TTL compatibility (VOH = 2.4 V @ IOUT = -40 A). 6. Output drivers are TTL compatible and will drive CMOS logic levels into a CMOS load. 4 DS211PP8 DS211F1
CS61581
ANALOG SPECIFICATIONS (TA = -40C to 85C; TV+, RV+ = 5.0 V 5%; GND = 0 V)
Parameter (Note 7) E1, 75 . (Note 8) E1, 120 . (Note 9) T1, (FCC Part 68) (Note 10) T1, DSX-1 (Note 11) External Equalizer Pulse Amplitude Transmitter Output Impedance (Note 13) Transformer turns ratio = 1:2 Low Z, Long Haul Transformer turns ratio = 1:1.5 E1, 75 . E1, 120 . T1, FCC T1, DSX1 T1, Ext. Equal (Note 12, 13) 10 Hz - 8 kHz 8k Hz - 40 kHz 10 Hz - 40 kHz Broad Band (Notes 7, 18) (Notes 7, 18) Transmitter AMI Output Pulse Amplitudes Min Typ Max Units
2.14 2.7 2.7 2.4 4.8
2.37 3.0 3.0 3.0 5.6 1.5 33 53 44 44 44
2.6 3.3 3.3 3.6 6.4
V V V V V
. . . . . .
Jitter Added by the Transmitter
Power in 2 kHz band about 772 kHz Power in 2 kHz band about 1.544 MHz (referenced to power in 2 kHz band at 772 kHz) Positive to Negative Pulse Imbalance (Notes 7, 13) Transmitter Short Circuit Current (Notes 7, 14)
12.6 -29 -
0.015 0.015 0.015 0.020 15 -38 0.2 -
17.9 0.5 50
UI UI UI UI dBm dB dB mA RMS
Notes: 7. Using a 0.47 F capacitor in series with the primary of a transformer recommended in the Applications Section. 8. Pulse amplitude measured at the output of the transformer across a 75 . load for line length settings LEN[2:0] = 001 and 000. 9. Pulse amplitude measured at the output of the transformer across a 120 . load for line length setting LEN[2:0] = 000. 10. Pulse amplitude measured at the output of the transformer across a 100 . load for line length setting LEN[2:0] = 000. 11. Pulse amplitude measured at the DSX-1 Cross-Connect for all line length settings from LEN[2:0] = 011 to LEN[2:0] = 111. 12. Assuming that jitter free clock is input to TCLK. Jitter Attenuator not in path. 13. Not production tested. Parameters guaranteed by design and characterization. 14. Measured broadband through a 0.5 . resistor across the secondary of the transmitter transformer during the transmission of an all ones data pattern with LEN[2:0] = 000 or 001.
DS211PP8
5
CS61581
ANALOG SPECIFICATIONS (Continued)
Parameter Receiver RTIP/RRING Input Impedance Sensitivity Below DSX (0 dB = 3.0 V) Long Haul, T1 Sensitivity Below DSX (0 dB = 3.0 V) Long Haul, E1 Sensitivity Below DSX (0 dB = 3.0 V) T1 - Short Haul Sensitivity Below G.703 (0 dB = 2.4 V) E1 - Short Haul Long Haul, T1 & E1 T1 Short Haul E1 Short Haul Data Decision Threshold (Note 18) (Note 15) T1, DSX-1 T1, (FCC Part 68) and E1 Allowable Consecutive Zeros before LOS Receiver Input Jitter Tolerance - Short Haul (Note 16) E1: 18 kHz - 100 kHz T1: 10 kHz - 100 kHz (Note 13) 2 kHz (Note 18) 10 Hz and below Receiver Input Jitter Tolerance - Long Haul (Note 17) E1:10 kHz - 100 kHz T1:10 kHz - 100 kHz (Note 13) 1 Hz Loss of Signal Threshold (Note 18) Min -40 30 -36 48 -21 270 -15 430 160 0.20 0.4 6.0 300 0.20 0.4 138 Typ 20k -42 -22 -16 50 50 175 Max 190 Units
. dB mV dB mV dB mV dB mV dB dB dB
% of peak % of peak bits UI UI UI UI UI UI UI
Notes: 15. Data decision threshold established after the receiver equalizer filters pulse overshoot and undershoot. 16. Jitter tolerance for 0 dB input signal level. Jitter tolerance increases at lower frequencies. See Figure 8. 17. See Receiver Jitter Tolerance Plot, Figure 8. 18. Guaranteed by design.
6
DS211PP8 DS211F1
CS61581
T1 SWITCHING CHARACTERISTICS (TA = -40C to 85C; TV+, RV+ = 5.0 V 5%;
GND = 0 V; Inputs: Logic 0 = 0 V, Logic 1 = RV+; See Figures 1, 2, & 3) Parameter TCLK Frequency MCLK Frequency RCLK Duty Cycle Rise Time, All Digital Outputs Fall Time, All Digital Outputs TPOS/TNEG to TCLK Falling Setup Time TCLK Falling to TPOS/TNEG Hold Time RPOS/RNEG Valid Before RCLK Falling RPOS/RNEG Valid Before RCLK Rising RPOS/RNEG Valid After RCLK Falling RPOS/RNEG Valid After RCLK Rising (Note 22) (Note 23) (Note 22) (Note 23) (Note 19) (Note 21) (Note 21) Symbol ftclk fmclk tr tf tsu2 th2 tsu1 tsu1 th1 th1 (Notes 18, 20) tpwh1/tpw1 25 25 150 150 150 150 Min Typ 1.544 1.544 50 274 274 274 274 85 85 Max Units MHz MHz % ns ns ns ns ns ns ns ns
Notes: 19. MCLK provided by an external source or TCLK. 20. RCLK duty cycle will be 62.5% or 37.5% when jitter attenuator FIFO limits are reached. 21. At max load of 1.6 mA and 50 pF. 22. Host Mode (CLKE = 1). 23. Host Mode (CLKE = 0)
E1 SWITCHING CHARACTERISTICS (TA = -40C to 85C; TV+, RV+ = 5.0 V 5%; GND = 0 V; Inputs: Logic 0 = 0 V, Logic 1 = RV+; See Figures 1, 2, & 3)
Parameter TCLK Frequency MCLK Frequency RCLK Duty Cycle Rise Time, All Digital Outputs Fall Time, All Digital Outputs TPOS/TNEG to TCLK Falling Setup Time TCLK Falling to TPOS/TNEG Hold Time RPOS/RNEG Valid Before RCLK Falling RPOS/RNEG Valid Before RCLK Rising RPOS/RNEG Valid After RCLK Falling RPOS/RNEG Valid After RCLK Rising (Note 22) (Note 23) (Note 22) (Note 23) (Note 19) (Note 21) (Note 21) Symbol ftclk fmclk tr tf tsu2 th2 tsu1 tsu1 th1 th1 (Notes 18, 20) tpwh1/tpw1 25 25 100 100 100 100 Min Typ 2.048 2.048 50 194 194 194 194 85 85 Max Units MHz MHz % ns ns ns ns ns ns ns ns
DS211PP8 DS211F1
7
CS61581
tr 90% 10% 90%
tf
Any Digital Output
10%
Figure 1. Signal Rise and Fall Characteristics
tpw1
RCLK
(CLKE = 1)
t pwl1 RPOS RNEG t su1
t pwh1 t h1
(CLKE = 0)
RCLK
Figure 2. Recovered Clock and Data Switching Characteristics
t pw2 t pwh2 TCLK TPOS/TNEG t su2 t h2
Figure 3. Transmit Clock and Data Switching Characteristics
8
DS211PP8 DS211F1
CS61581
SWITCHING CHARACTERISTICS (TA = -40 to 85C; TV+, RV+ = 5V 5%;
Inputs: Logic 0 = 0 V, Logic 1 = RV+) Parameter SDI to SCLK Setup Time SCLK to SDI Hold Time SCLK Low Time SCLK High Time SCLK Rise and Fall Time CS to SCLK Setup Time SCLK to CS Hold Time CS Inactive Time SCLK to SDO Valid CS to SDO High Z Notes: 24. Output load capacitance = 50 pF (Note 24) Symbol tdc tcdh tcl tch tr, tf tcc tcch tcwh tcdv tcdz Min 50 50 240 240 50 50 250 Typ 100 Max 50 200 Units ns ns ns ns ns ns ns ns ns ns
t cwh CS t cc SCLK t ch t cch t cl t cdh LSB BYTE DATA BYTE
t dc
SDI LSB CONTROL
t cdh MSB
Figure 4. Serial Port Write Timing Diagram
CS
SCLK
SDI
LAST ADDR BIT
t cdv SDO CLKE = 0
D0 D1 D6 D7
t cdz
t cdv
D0 D1 D6 D7
SDO CLKE = 1
HIGH Z
Figure 5. Serial Port Read Timing Diagram DS211PP8 DS211F1 9
CS61581
2. THEORY OF OPERATION
The CS61581 Universal Line Interface supports T1 and E1 data rates for both short haul and long haul applications. The transmitter complies with all standard T1 and E1 applications without changing transformers. Transmitter power consumption is minimized using the impedance matching feature, which eliminates external resistors for standard line impedances. When configured for long haul operation, the receiver uses gain and equalization to provide 40 dB of sensitivity. The receiver reconfigures for short haul operation, limiting the receive sensitivity and increasing the noise immunity. If MCLK is provided, the crystal oscillator is ignored.
2.3
Transmitter
The transmitter accepts digital T1 or E1 input data and drives appropriately shaped AMI (Alternate Mark Inversion) pulses onto a transmission line through a transformer. The transmit data (TPOS & TNEG or TDATA) is sampled on the falling edge of the input clock, TCLK. Upon power up, the CS61581 defaults to Long Haul Mode with low-impedance drive. In this mode, a 1:2 transformer is required (See Table 1). The CS61581 will support both T1 and E1 operation as determined by the master clock frequency. In host mode, T1 (DSX-1 or Network Interface), E1 (ITU-T or G.703) or T1 long-haul pulse shapes may be selected. Long-haul or short-haul operation is determined by the SH/LH bit (CR2.0). The SH/LH bit also establishes functionality of Control Registers 1 and 2. In the matched impedance configuration, the line driver internally matches the impedance of the line load; 75 . or 120 . for E1, and 100 . for T1 using a 1:1.5 turns ratio transformer. Internal impedance matching reduces current consumption by about a factor of two compared to return loss achieved by external resistors. The T1 long-haul pulse shapes comply with FCC Part 68 Option A (0 dB). Option B (-7.5 dB), Option C (-15 dB) or (-22.5 dB) (see Table 1). If desired, the T1 pre-equalization settings can be selected for E1 operation as well. In long-haul mode, pulse shaping and signal level are controlled by LBO1 and LBO2 pins or register bits. Custom transmit pulse shapes may be implemented by writing pulse shape coefficients to the registers. Custom pulses may be used to correct for pulse shape degradation or distortion caused by improper termination, suboptimal interconnect wiring, or
2.1
Operating Mode Selection
The CS61581 can be operated in stand-alone hardware interface mode (MODE pin is low), or by a microcontroller in serial host mode (MODE pin is high). Additional functionality is available in the host mode including both short haul and long haul operational modes. The CS61581 defaults to the Long Haul configuration (LXT310/318 compatible). The T1 (DSX-1 and Network interface) and E1 (ITU-T G.703) are selectable via the serial port by writing to a control register. Tying TNEG high for more than 16 TCLK cycles enables the unipolar mode, changing TPOS to TDATA, RPOS to RDATA, and RNEG to BPV. When configured for unipolar mode, the MODE pin can be tied to RCLK enabling the B8ZS encoders and decoders. Coder mode does not support bipolar data.
2.2
Master Clocks
The CS61581 requires a reference clock for the receiver and the jitter attenuator. Either a 1.544 MHz (or 2.048 MHz) external clock can be input to MCLK, or a 4X crystal can be connected to the onchip oscillator. This frequency reference should be within 100 ppm of the nominal operating frequency. Jitter and wander on the reference clock will degrade jitter attenuation and receiver jitter tolerance.
10
DS211PP8 DS211F1
CS61581
Long Haul
LB02 0 0 1 1 LB01 0 1 0 1 Output Pulse 0 dB -7.5 dB -15 dB -22.5 dB Transformer Turns Ratio Mode Transmit Receive HDW or MATCHZ* = 0 1:2 1:1 MATCHZ* = 1 1:1.5 1:1
* MATCHZ = CR2.5 Short Haul
LEN2 0 0 0 1 1 1 1 0 0 LEN1 0 0 1 0 0 1 1 1 1 LEN0 0 1 1 0 1 0 1 1 0 Output Pulse E1 2.37 V E1 3.0 V DSX-1 0'-133' DSX-1 133'-266' DSX-1 266'-399' DSX-1 399'-533' DSX-1 533'-655' ANSI T1.403 FCC Part 68, 6.0 V Option A Line Z 75. 120. 100. 100. 100. 100. 100. 100. 100.
Table 1. Pulse Shape Selection and Transformer Requirements
loading from external components such as high voltage protection devices. For T1 DSX-1 applications, line lengths from 0 to 655 feet (as measured from the transmitter to the DSX-1 cross connect) may be selected. The five partition arrangement in Table 1 meets ANSI T1.102 pulse shape requirements when using #22 ABAM or AT&T 600 series cable. A typical output pulse is shown in Figure 6. These pulse settings can also be used to meet ITU-T pulse shape requirements for 1.544 MHz operation. Short haul pulse shapes for T1 and E1 are selected by the LEN[2:0] bits in Control Register 1. Note that when the device is operated at E1 frequency in the hardware mode, it defaults to low impedance, long haul mode. The pulses driven by the transmitter in this mode are T1.403 (350ns) pulses with an overshoot and an undershoot. To drive
DS211PP8 DS211F1
pulses without overshoot and undershoot in E1 long haul mode, the E1_LH bit (CR3.6) must be set to 1, with the SH/LH bit (CR2.0) set to 0. The E1 G.703 pulse shape is supported with line length selections LEN[2:0] = 000 for 2.37 V 75. applications or LEN[2:0] = 001 for 3.0 V 120 . applications. The output pulse will meet the G.703 pulse shape template shown in Figure 7. The output impedance of the driver will adjust according to the pulse shape selected. In the short haul mode, setting the LEN[2:0] bits also controls the transmitter output impedance. For long haul operation, driver impedance is determined by the desired selection of MATCHZ and E1_LH bits. When MATCHZ is set to "0" the output impedance is low, and the impedance presented to the line is controlled by external resistors. When MATCHZ is set to 1, E1_LH determines whether
11
CS61581
NORMALIZED AMPLITUDE 1.0
Percent of nominal peak voltage 120 110 244 ns 194 ns
ANSI TI.102, AT&T CB 119 SPECIFICATIONS
269 ns
0.5
100
90 80
0 OUTPUT PULSE SHAPE -0.5 0 250 750 500 TIME (nanoseconds) 1000
10 0 -10 -20 219 ns 488 ns Nominal Pulse
50
Figure 6. Typical Pulse Shape at DSX-1 Cross Connect
the driver is set for 100. (E1_LH = 0) or 120. (E1_LH = 1). The CS61581 will detect the absence of TCLK, and will force TTIP and TRING to high impedance after 175 bit periods, preventing transmission when data input is not present. In host mode, the transmitter can be set to high impedance by setting the TxHIZ bit, CR2.1, to "1." When any transmit control bit (TAOS, LEN0-2, LBO1-2, or LLOOP) is toggled, the transmitter outputs will require approximately 22 bit periods to stabilize. The transmitter will take longer to stabilize when RLOOP is selected because the timing circuitry must adjust to the new frequency. The CS61581 has the option to drive a 6 Vpeak pulse. The option is used for driving external equalizers used in T1 DSX applications that conform to FCC Part 68, Option A. This configuration is selected by setting the LEN[2:0] control bits in register 0x10 to 010 in the short haul configuration. The
Figure 7. Mask of the Pulse at the 2048 kbps Interface
turns ratio of the transmit transformer must be set accordingly: in Matched Impedance mode, the turns ratio must be 1:1.5; in Low Impedance mode, the transformer turns ratio = 1:2.6.
2.4
Transmit All Ones Select
The transmitter provides for all ones insertion at the frequency of TCLK. If TCLK is absent, then MCLK is used (or the quartz crystal generated frequency in the absence of MCLK). Transmit all ones is selected when TAOS (pin 28 in hardware mode, CR1.7 in host mode) goes high, and causes continuous ones to be transmitted on the line (TTIP and TRING). When TAOS is active, the TPOS and TNEG (TDATA) inputs are ignored. If Remote Loopback is in effect, any TAOS request will be ignored.
12
DS211PP8 DS211F1
CS61581
2.4.1 Receiver
thresholds are dynamically established at 50% percent of the peak level. This is acceptable for both T1 and E1 cases as pulse undershoot and overshoot are filtered internally.
The receiver extracts data and clock from the input signal and outputs clock and synchronized data. The RTIP and RRING inputs are biased to an intermediate DC level so that the input is received as a differential signal. The incoming pulses are amplified, equalized and filtered before being fed to the comparator for peak detection, slicing and data recovery. A noise and cross-talk filter removes signal components that are coupled onto the line from other cables. T1 or E1 operation is determined by the transmit pulse shape selection, LEN[2:0]. The clock and data recovery circuit exceeds the jitter tolerance specifications of Publications 43802, 43801, AT&T 62411, TR-TSY-000170, ITU-T G.823 and ETSI TBR12/13. Jitter tolerance is shown in Figure 8. In Hardware mode, the receiver is configured for Long Haul operation. In Host mode Short Haul operation can be selected by setting the SH/LH (CR2.0) to 1. When configured for short haul, the functions of registers 0x10 and 0x11 are redefined.
2.4.3
Long Haul
Configuring the receiver for long haul operation increases the receive sensitivity. To select long haul mode, the SH/LH (CR2.0) bit must be set to 0; for E1 long haul mode, the E1_LH bit (CR3.6) must be set to 1.
2.4.4
Clock Recovery
The clock recovery circuit is a third-order phase lock loop. The clock and data recovery circuit is tolerant of long strings of consecutive zeros, and will successfully receive a 1-in-175, jitter-free input signal. In Hardware mode, data on RPOS and RNEG (RDATA), is stable on the rising edge of recovered clock, RCLK. In host mode, CLKE (pin 28) determines the clock polarity for which output data is valid, as shown in Table 2. When CLKE is high, RPOS and RNEG (RDATA) are valid on the falling edge of RCLK. When CLKE is low, RPOS and RNEG are valid on the rising edge of RCLK.
2.4.2
Short Haul
Receiver sensitivity is set to comply with ITU-T I.431 requirements for E1 and T1. The comparator
300
Minimum Performance
138 100
AT&T 62411 28
MODE (pin 5) LOW HIGH
CLKE Clock Edge for DATA CLOCK (pin 28) Valid Data Don't Care LOW RPOS RNEG RPOS RNEG SDO RPOS RNEG SDO RCLK RCLK RCLK SCLK RCLK RCLK SCLK Rising Rising Rising Falling Falling Falling Rising
10
PEAK-TO-PEAK JITTER (unit intervals) 1
G. 823
.4
.1 1 10 100 300 700 1k JITTER FREQUENCY (Hz) 10k 100k
HIGH
HIGH
Figure 8. Minimum Input Jitter Tolerance of Receiver
Table 2. Data Output/Clock Relationship
DS211PP8 DS211F1
13
CS61581
2.4.5 Jitter Tolerance
The jitter attenuator is enabled if an external crystal is connected. If no crystal is present, then the jitter attenuator is enabled by either grounding or floating XTALIN (pin 9). It is disabled by tying XTALIN high. It is placed in the transmit or receive paths by setting JASEL (pin 11) either low or high, respectively. The jitter attenuator has two modes of operation depending on whether the CS61581 is configured for T1 or E1 operation (based on the output pulse shape selection). For T1, the jitter attenuator corner frequency is set at 4 Hz, with attenuation increasing at a 20 dB per decade rate above 4 Hz. For E1 the corner frequency is approximately 1.25 Hz in order to comply with ETSI 300 011, TBR12/13, and recommendation I.431 Complying to these specifications also guarantees compliance to less stringent standards, such as G.736. Typical jitter attenuation curves are shown in Figures 10 and 11.
The receiver jitter tolerance is shown in Figure 8. The CS61581 jitter tolerance exceeds AT&T 62411 in T1 applications, and G.823 in E1 applications.
2.5
Receiver Line Attenuation Indication
LATN (pin 18) outputs a coded signal that represents the signal level at the input of the receiver. As shown in Figure 9, the LATN output is measured against RCLK to provide the signal level in 7.5 dB increments. In host mode, the receive input signal level can be read from the Equalizer Gain register (address 0x12), to greater resolution, dividing the input range into 20 steps of 2 dB increments.
2.6
Jitter Attenuator
The jitter attenuator reduces the amount of jitter and wander in the input signal. the jitter attenuator is built around a FIFO; the write pointer of the FIFO is driven by the input clock, and the read pointer is driven by a phase locked loop (PLL). The jitter attenuator can be placed in either the transmit or receive paths; in the transmit path, writing to the FIFO is controlled by TCLK; if the jitter attenuator is in the receive path, writing is controlled by the recovered clock from the input data. The jitter attenuator does not require an external crystal. If a crystal is present, the PLL uses it for a reference; otherwise, MCLK provides the reference.
2.7
Receiver Loss of Signal
The receiver will indicate loss of signal by asserting LOS (pin 12, also CR1.0 in host mode). This happens on power up, reset, when the receiver gain reaches its maximum, or on receiving 175+/-15 consecutive zeros. Received zeros are counted based on recovered clock cycles. When in the LOS state, received data is not output from RPOS/RNEG (RDATA); but is squelched until the device comes out of LOS. The LOS condition is ex-
RCLK
LATN
1
2
3
4
5
LATN = 1 RCLK, 7.5 dB of Attenuation LATN = 2 RCLK, 15 dB of Attenuation LATN = 3 RCLK, 22.5 dB of Attenuation
LATN = 4 RCLK, 0 dB of Attenuation
Figure 9. LATN Pulse Width encoding 14 DS211PP8 DS211F1
CS61581
0 10 Attenuation in dB 20 30 40 50 60 1 10 100 Maximum Attenuation Limit Measured Performance 1k 10 k 62411 Requirements Minimum Attenuation Limit
these signal levels. These LOS thresholds are compliant with all Short Haul applications. In LOS, the RCLK frequency depends on whether MCLK is applied, and whether the jitter attenuator is in the transmit or receive path. If the jitter attenuator is in the receive path, the jitter attenuator will hold over the average incoming data frequency prior to LOS. RPOS (RDATA) and RNEG pins are forced low upon LOS. When the jitter attenuator is in the transmit path or not used, the clock recovery is referenced to MCLK, if provided, or the crystal oscillator. The frequency of RCLK in this case will simply remain slaved to the clock reference upon loss of data. The recovered clock remains as a 50% duty cycle clock. The digital PLL in the clock recovery circuit of the CS61581 generates an internal data clock from the edges of the incoming pulses (1's). Timing is recovered by a phase selector which selects one of the phases from the internal synchronization clock (one of three clocks, 120 degrees apart in phase, at 16X the data rate). Since the selection is made between a limited set of phases, the Digital Timing Recovery process has a small phase error built into the sampling process. By choosing 48 possible sampling phases, the CS61581 reduces the sampling error to a minimum.
Frequency in Hz
Figure 10. Typical Jitter Transfer Function - T1
0
G.736
10 Attenuation in dB 20
TBR12/13
Minimum Attenuation Limits
30 40 50 60 1 20 2400
Measured Performance
18 k 100 k
Frequency in Hz
Figure 11. Typical Jitter Transfer Function - E1
2.8
Local Loopback
ited using the ANSI T1.231-1993 and ITU-T G.775 criteria, namely 12.5% ones density for 175+/-75 bit periods with no more than 100 consecutive zeros. In Long Haul operation, the receiver recovers signals down to -40 dB for T1 and -36 dB for E1. In Short Haul mode, the receive sensitivity is typically 21 dB for T1 and -15 dB for E1, in accordance with I.431 and G.775. LOS will be declared beyond
Local loopback is selected by setting LLOOP high (pin 27 in Hardware mode, CR1.6 in Host mode). Selecting local loopback causes the clock and data on TCLK, TPOS and TNEG (TDATA) to be output on RCLK, RPOS and RNEG (RDATA). The RTIP/RRING inputs have no effect on RCLK, RPOS and RNEG (RDATA) in this mode. Inputs to the transmitter are still transmitted on TTIP and TRING unless TAOS has been selected, in which case AMI-encoded continuous ones are transmitted at the TCLK frequency.
DS211PP8 DS211F1
15
CS61581
2.9 Remote Loopback
The Network Loopback generation and detection functions are only available in Long Haul mode.
Remote loopback is selected by setting RLOOP high (pin 26 in Hardware mode, CR1.5 in Host mode). In remote loopback, the recovered clock and data input on RTIP and RRING are sent back out on the line via TTIP and TRING. Selecting remote loopback overrides a TAOS request. The recovered clock and data from the incoming signal are also sent to RCLK, RPOS and RNEG (RDATA). Simultaneous selection of local and remote loopback modes will cause a device reset to occur (see Reset).
2.11
Alarm Indication Signal
The receiver sets the register bit, AIS, to "1" when less than 9 zeros are detected out of 8192 bit periods. AIS returns to "0" upon the first read after the AIS condition is removed, determined by 9 or more zeros out of 8192 bit periods. Some operations change the definition of other bits. Writing a 1 or 0 to SH/LH (CR2.0 = 1), places the device in Short Haul or Long Haul mode respectively, and the definition of Control Registers 1 and 2 are modified accordingly. In Long Haul mode, E1 operation can be enabled by setting E1_LH to 1 (CR3.6 = 1), changes CR1.2 from B8ZS to HDB3. Enabling unipolar mode by setting TNEG (pin 4) high for 16 clocks allows the user to enable coder mode using the CODER bit (CR1.2LH). When TNEG is low, enabling bipolar mode, CR1.2LH is the TAZ bit (transmit all zeroes).
2.10
Network Loopback
During Network Loopback (automatic remote loopback), the data path and operation of the device is identical to Remote Loopback, except this loopback mode is controlled by the transmitter at the other end of the loop. It is initiated by enabling Network Loopback detection on the device. In Host Mode, Network Loopback (NLOOP) detection is enabled by writing ones to TAOS, LLOOP and RLOOP, then clearing them. In hardware mode, Network Loopback can be enabled by tying RLOOP to RCLK or by setting TAOS, LLOOP, and RLOOP high for at least 200 ns, and then low. Once enabled Network Loopback functionality will remain in effect until RLOOP is activated or the device is reset. When NLOOP detection is enabled, the receiver monitors the input data stream for the LOOP UP data pattern: a repeating 00001. When this pattern is repeated for a minimum of five seconds (with less than 10-3 BER), the device sets its internal data path as in Remote Loopback. It stays in this mode until the LOOP DOWN pattern (repeating 001) is received for 5 seconds, or by activation of RLOOP. NLOOP is temporarily suspended by LLOOP, but the NLOOP state is not reset. The device can also generate the LOOP UP and LOOP DOWN sequences by setting the LOOPUP (CR2.3) or LOOPDN (CR2.4) bits respectively.
2.12
Serial Interface
In the Host Mode, pins 24 through 28 serve as a microcontroller interface. On-chip registers can be written to via the SDI pin or read from via the SDO pin at the clock rate determined by SCLK. Through these registers, a host controller can be used to control operational characteristics and monitor device status. The serial port read/write timing is independent of the system transmit and receive timing. Data transfers are initiated by taking the chip select input, CS, low (CS must initially be high). Address and input data bits are clocked in on the rising edge of SCLK. The clock edge on which output data is stable and valid is determined by CLKE as shown in Table 2. Data transfers are terminated by setting CS high. CS may go high no sooner than 50 ns after the rising edge of the SCLK cycle corresponding to the last write bit. For a serial data read, CS may go high any time to terminate the output and set SDO to high impedance.
DS211PP8 DS211F1
16
CS61581
Figure 12 shows the timing relationships for data transfers when CLKE = 0. When CLKE = 1, data bit D7 is held until the falling edge of the 16th clock cycle. When CLKE = 0, data bit D7 is held valid until the rising edge of the 17th clock cycle. SDO goes high-impedance after CS goes high or at the end of the hold period of data bit D7. SDO goes to a high impedance state when not in use. SDO and SDI may be tied together in applications where the host processor has a bidirectional I/O port. An address/command byte, shown in Figure 12, points to addresses 0x10 through 0x15 (address 0x10 shown), and precedes a data byte. The first bit of the address/command byte determines whether a read or a write is requested. The next six bits contain the address. The last bit is ignored. Data to the internal registers is input on the eight clock cycles immediately following the address/command byte. The register bit assignments are shown in Table 3.
CS SCLK SDI SDO CLKE = 0 R/W 0 0 0 0 1 0 0 D0 D0 D1 D1 D2 D3 D4 D5 Data Input/Output D2 D3 D4 D5 D6 D6 D7 D7
Address/Command Byte
Figure 12. Input/Output Timing (showing address 0x10)
7
6
LLOOP LLOOP
5
RLOOP RLOOP
4
LB02 LEN2
3
LB01 LEN1 LOOPUP RCODER EQ3 INS_QERR -
2
CODER TAZ LEN0 RPWDN TCODER EQ2 QSYNC TEST -
1
NLOOP RSVD TxHIZ TxHIZ EQ1 QGEN -
0
LOS LOS SH/LH SH/LH EQ0 LSB TEST LSB
ADDR
0x10 R/W 0x10 R/W 0x11 R/W 0x11 R/W 0x12 R 0x13 R/W 0x14 R/W 0x15 R
Control Register 1 LH
(CR2.0 = 0) (CR1LH)
TAOS TAOS AIS AIS X MSB QRSSPATH MSB
Control Register 1 SH
(CR2.0 = 1) (CR1SH)
Control Register 2 LH
(CR2.0 = 0) (CR2LH)
RAMPLSE MATCHZ LOOPDN RAMPLSE MATCHZ X E1_LH X RST_ QERR RSVD EQ4 QDET -
Control Register 2 SH
(CR2.0 = 1) (CR2SH)
Equalizer Gain
(EQGAIN)
RAM Address
(RAM)
Control Register 3
(CR3)
Data Pattern Error Count
(DPEC)
Table 3. Register Map
DS211PP8 DS211F1
17
CS61581
2.13 Control Register 1 LH (CR2.0 = 0): Address 0x10
6 LLOOP 5 RLOOP 4 LB02 3 LB01 2 CODER TAZ 1 NLOOP 0 (LSB) LOS
7 (MSB) TAOS
TAOS LLOOP
Transmit All Ones Select When TAOS = 1, all ones are transmitted at the TCLK frequency Local Loopback When LLOOP = 1, data input at TPOS, TNEG (TDATA) is internally looped back and output on RPOS, RNEG (RDATA). TCLK is routed to RCLK, through the jitter attenuator, if activated. Remote Loopback When RLOOP = 1, clock and data recovered by the receiver are sent back through the transmit path and retransmitted. The clock and data are routed through the jitter attenuator, if activated. Line Build Out LBO2 LBO1 Attenuation 0 0 0 dB 0 1 -7.5 dB 1 0 -15 dB 1 1 -22.5 dB For E1 long haul, only the 0 dB setting should be used when the part is configured for matched impedance drive. Zero Substitution (valid only when TNEG (UBS) is tied high, invoking unipolar mode). In Long Haul mode, setting CODER to "1" enables B8ZS (HDB3) encoding and decoding. The substitution depends on whether the CS61581 is configured for T1 or E1 operation. via the E1_LH bit, CR3.6 Transmit All Zeroes (valid only when TNEG (UBS) is tied low, invoking bipolar mode). When in bipolar mode (TPOS/TNEG are data inputs) setting TAZ to "1" causes all zeros to be transmitted. Network Loopback NLOOP = 1 when a network loopback code has been detected on the received signal. An interrupt will occur when NLOOP changes state unless a "1" is written to NLOOP disabling the interrupt. Loss Of Signal LOS = 1 when the loss of signal criteria have been met (175 zeros). LOS = 0 when a valid signal is being received. An interrupt will occur when LOS changes state unless a "1" is written to LOS disabling the interrupt.
RLOOP
LBO[2:1]
CODER
(TAZ)
NLOOP
LOS
18
DS211PP8 DS211F1
CS61581
2.14 Control Register 1 SH (CR2.0 = 1): Address 0x10
6 LLOOP 5 RLOOP 4 LEN2 3 LEN1 2 LEN0 1 RSVD 0 (LSB) LOS
7 (MSB) TAOS
TAOS LLOOP
Transmit All Ones Select When TAOS = 1, all ones are transmitted at the TCLK frequency Local Loopback When LLOOP = 1, data input at TPOS/TNEG (TDATA) is internally looped back and output on RPOS/RNEG (RDATA). TCLK is routed to RCLK, through the jitter attenuator, if activated. Remote Loopback When RLOOP = 1, clock and data recovered by the receiver are sent back through the transmit path and retransmitted. The clock and data are routed through the jitter attenuator, if activated. Line Length Selection Allows selection of a variety of transmit pulse shapes. See Table 1 for details. Note that the selection of T1 or E1 pulse shapes determines the operation of the device. When MATCHZ is set to "1" the transmitter's output impedance changes according to the pulse selected. For T1 pulses, the encoders and decoders are set to B8ZS, and the QRSS data pattern is 220-1 with 14 consecutive zeros, max. For E1 pulses, the encoders and decoders are set to HDB3, and the QRSS data pattern is 215-1. This bit is reserved. Loss Of Signal LOS = 1 when the loss of signal criteria have been met (175 zeros). LOS = 0 when a valid signal is being received. An interrupt will occur when LOS changes state unless a "1" is written to LOS disabling the interrupt.
RLOOP
LEN [2:0]
RSVD LOS
DS211PP8 DS211F1
19
CS61581
2.15 Control Register 2 LH: Address 0x11
6 RAMPLSE 5 MATCHZ 4 LOOPDN 3 LOOPUP 2 RPWDN 1 TxHIZ 0 (LSB) SH/LH
7 (MSB) AIS
AIS
Alarm Indication Signal. AIS = 1 when an all ones pattern is present at the receiver. This bit is reset to "0" by the first read occurring after the AIS condition has cleared. An interrupt will occur when AIS is present unless a "1" is written to AIS disabling the interrupt. When RAMPLSE = 1, output pulse shapes are determined by the codes in the internal, programmable, transmit RAM. Matched Impedance Drive When MATCHZ = 1 the output impedance is automatically set to match the impedance of a standard T1 or E1 line. A 1:1.5 transformer should be used when MATCHZ = 1, and a 1:2 transformer should be used when MATCHZ = 0. (See Figures 15 and 16.) Loop Down In Long Haul mode, setting LOOPDN to "1" causes the data pattern 001001... to be repetitively transmitted. Loop Up In Long Haul mode, setting LOOPUP to "1" causes the data pattern 0000100001... to be repetitively transmitted. Receiver Power Down When RPWDN = 1, the receiver circuitry is powered down, but the transmitter is still active. Transmitter High Impedance When TxHIZ = 1 the transmitter goes to a low-power, high-impedance state Short Haul / Long Haul Select When SH/LH = 0, the CS61581 is in the Long Haul mode. When SH/LH = 1, the CS61581 is in the Short Haul mode. Note that it overwrites the E1_LH bit, if set. SH/LH controls the functions of the bits in Control Register 1 (address 0x10) and Control Register 2 (address 0x11).
RAMPLSE MATCHZ
LOOPDN
LOOPUP
RPWDN TxHIZ SH/LH
20
DS211PP8 DS211F1
CS61581
2.16 Control Register 2 SH: Address 0x11
6 RAMPLSE 5 MATCHZ 4 RSVD 3 RCODER 2 TCODER 1 TxHIZ 0 (LSB) SH/LH
7 (MSB) AIS
AIS
Alarm Indication Signal. AIS = 1 when an all ones pattern is present at the receiver. This bit is reset to "0" by the first read occurring after the AIS condition has cleared. An interrupt will occur when AIS is present unless a "1" is written to AIS disabling the interrupt. When RAMPLSE = 1, output pulse shapes are determined by the codes in the internal RAM. Matched Impedance Drive When MATCHZ = 1 the output impedance is automatically set to match the impedance of a standard T1 or E1 line. A 1:1.5 transformer should be used when MATCHZ = 1, and a 1:2 transformer should be used when MATCHZ = 0. (See Figures 15 and 16.) Reserved. Set to "0" for normal operation. Receive Decoder Enable In Short Haul mode, when TNEG is held high, setting RCODER to "1" causes the received data to be B8ZS/HDB3 decoded (depends on T1 or E1 pulse shape selection). When RCODER is set to "0" the decoders are set for AMI only. This bit has precedence over the external pin. Transmit Encoder Enable In Short Haul mode, when TNEG is held high, when TCODER = 1 the transmitter B8ZS/HDB3 encoders are enabled (depends on T1 or E1 pulse shape selection). When TCODER is set to "0" the decoders are set for AMI only. This bit has precedence over the external pin. Transmitter High Impedance When TxHIZ = 1 the transmitter goes to a low-power, high-impedance state Short Haul / Long Haul Select When SH/LH = 0, the CS61581 is in the Long Haul mode. When SH/LH = 1, the CS61581 is in the Short Haul mode. SH/LH controls the functions of the bits of Control Register 1 (address 0x10), and Control Register 2 (address 0x11).
RAMPLSE MATCHZ
RSVD RCODER
TCODER
TxHIZ SH/LH
2.17
Equalizer Gain (EQGAIN): Address 0x12
6 X 5 X 4 EQ4 3 EQ3 2 EQ2 1 EQ1 0 (LSB) EQ0
7 (MSB) X
EQ[4:0]
The receive equalizer gain settings are broken down into 20 segments and provided at the five LSBs of this register, EQ4 - EQ0. 00001 corresponds to -2 dB, 10100 corresponds to -40 dB. The three MSBs are don't cares.
2.18
RAM Address (RAM): Address 0x13
6 RAM.6 5 RAM.5 4 RAM.4 3 RAM.3 2 RAM.2 1 RAM.1 0 (LSB) RAM.0
7 (MSB) RAM.7
RAM[7:0]
The RAM address pointer for the arbitrary waveform memory; a special write procedure must be followed to write the waveform RAM.
DS211PP8 DS211F1
21
CS61581
2.19 Control Register 3 (CR3): Address 0x14
6 E1_LH 5 RST_QERR 4 QDET 3 INS_QERR 2 QSYNC/Test 1 QGEN 0 (LSB) Test
7 (MSB) QRSSPATH
QRSSPATH
When QRSSPATH = 0 the QRSS pattern will be output from the recovered data pins, RPOS, RNEG (RDATA), and may be received at the transmitter inputs, TPOS, TNEG (TDATA). When QRSSPATH = 1 the QRSS pattern will be output from the line transmitter and may be received at the receiver. E1 Long Haul When E1_LH = 1 and SH/LH (CR2.0) = 0, the following functionality applies: Coder mode selects HDB3 coding and decoding; when MATCHZ = 1, the output impedance of the transmitter will be set to match impedances near 120. ; the QRSS pattern is 215-1; the jitter attenuator is adjusted for TBR12/13 compliance, with the knee in the frequency response at 1.25 Hz. When E1_LH = 0 and SH/LH = 0, the following functionality applies: Coder mode selects B8ZS coding and decoding; when MATCHZ = 1, the output impedance of the transmitter will be set to match impedances near 100. ; the QRSS pattern is 220-1; the jitter attenuator is adjusted for AT&T 62411 compliance, with the knee in the frequency response at 4 Hz. This bit is ignored if SH/LH = 1. Reset Data Pattern Error Count Register Setting RST_QERR to "1" will clear the QRSS error count in the DPEC register. This bit is automatically cleared and will read as "0." QRSS Detector Enable When QDET = 1, the QRSS pattern detector is enabled. Errors detected and counted are stored in the DPEC register (address 0x15). QRSS Error Insert Setting INS_QERR to "1" and then "0" causes an error to be inserted in the output QRSS pattern. QSYNC reads as "1" to indicate when the QRSS detector is synchronized to an input pattern. QSYNC is only valid when QDET = 1 enabling the pattern detector. When writing this register, this bit must be set to "0" for normal operation. QRSS Generator Enable When QGEN = 1, the QRSS generator is enabled. The QRSS pattern is output at the TTIP/TRING pins, or at the RPOS/RNEG (RDATA) pins, depending upon the state of the QRSSPATH bit. Errors can be generated using the INS_QERR bit. Bit should be set to "0" for normal operation.
E1_LH
RST_QERR
QDET
INS_QERR
QSYNC/Test
QGEN
Test
2.20
Data Pattern Error Count (DPEC): Address 0x15
6 5 4 3 2 1 0 (LSB)
7 (MSB)
DPEC.7 DPEC[7:0]
DPEC.6
DPEC.5
DPEC.4
DPEC.3
DPEC.2
DPEC.1
DPEC.0
Errors detected in the input QRSS pattern are counted and stored. This register saturates at 255 errors. The DPEC is cleared when the RST_QERR bit is written in the CR3 register.
22
DS211PP8 DS211F1
CS61581
2.21 Interrupts 3. QRSS TEST MODE
In Host Mode, the CS61581 has the capability to generate and detect a QRSS (220-1 with 14 zeros _PATH bit (CR3.7) determines whether the pattern is transmitted on TTIP/TRING or RPOS/RNEG. Errors can be inserted and counted in the pattern. The QRSS test mode is controlled through Control Register 3, address 0x14. Setting QGEN to 1 (CR3.1 = 1) initiates the pattern output. The QRSS pattern detector is enabled by writing a 1 to QDET (CR3.4 = 1). When the detector synchronizes to an input pattern, QSYNC is set to 1. Errors detected in the received QRSS pattern are counted and stored in the Data Pattern Error Count, DPEC, register at address 0x15. An error can be inserted in the output data pattern by setting INS_QERR bit to 1 then 0. The number of errors accumulated by the pattern detector are stored in the DPEC register. The DPEC register will accumulate to all ones, 255 errors, and stay at that level until reset. The DPEC register is reset to zero by setting the RST_QERR bit to 1 (CR3.3 = 1)
An interrupt will occur (INT pulls low) in response to a change in the LOS, AIS or NLOOP bits. The interrupt is cleared when the host processor writes a "1" to the respective bit in the control register. Writing a "1" to LOS or NLOOP over the serial interface has three effects: 1) The current interrupt on the serial interface will be cleared. (Note that simply reading the register bits will not clear the interrupt). 2) Output data bits 5, 6 and 7 will be reset as appropriate. 3) Interrupts for the corresponding LOS and NLOOP will be prevented from occurring. Writing a "0" to either LOS or NLOOP enables the corresponding interrupt for LOS and NLOOP. Reading the registers returns their current status or setting. Register 0x10 outputs the status NLOOP and LOS and has bits 5, 6, and 7 encoded as shown in Tables 4 and 5.
Bits 7 0 0 0 0 1 1 1 1 6 0 0 1 1 0 0 1 1 5
Long Haul Mode Status Bits 7 0 0 0 0 1 1 1 1 6 0 0 1 1 0 0 1 1 5 Short Haul Mode Status
0 Reset has occurred, or no program input 1 RLOOP active 0 LLOOP active 1 LOS has changed state since last Clear LOS occurred 0 TAOS active 1 NLOOP has changed state since last Clear NLOOP occurred 0 TAOS and LLOOP active 1 LOS and NLOOP have both changed state since last Clear NLOOP and Clear LOS Table 4. Register 0x10 Decoding
0 Reset has occurred, or no program input 1 RLOOP active 0 LLOOP active 1 LOS has changed state since last Clear LOS occurred 0 TAOS active 1 Not used 0 TAOS and LLOOP active 1 Not Used Table 5. Register 0x10 Decoding
DS211PP8 DS211F1
23
CS61581
4. ARBITRARY WAVEFORM GENERATION
In addition to the predefined pulse shapes, the user can create custom pulse shapes using the host mode. This flexibility allows the board designer to accommodate non-standard cables, EMI filters, protection circuitry, etc. The arbitrary pulse shape of mark (a transmitted 1) is specified by describing it's pulse shape across three Unit Intervals (UIs). This allows, for example, the long-haul return-to-zero tail to extend into the next UI, or two UIs, as is required for isolated pulses. Each UI is divided into multiple phases, and the users defines the amplitude of each phase. The waveform of a space (a transmitted 0) is fixed at zero volts. Examples of the phases are shown in Figure 13. In all cases, to define an arbitrary waveform, the user writes to the Waveform Register either 36, 39 or 42 times (12, 13 or 14 phases per UI for three UIs). The phases are written in the order: UI1/phase1, UI1/phase2,..., UI1/phase14, UI2/phase1,..., UI2/phase14, UI3/phase1,..., UI3/phase14. For E1, short haul applications the CS61581 divides the 488 ns UI into 12 uniform phases (40.7 ns each), and will ignore the phase amplitude information written for phases 13 and 14 of each UI. For DSX-1 and DS1 applications, the CS61581 divides the 648 ns UI into 13 uniform phases (49.8 ns each), and will ignore the phase amplitude information written for phase 14 of each UI. For E1 long haul applications, the CS61581 divides the 648 ns UI into 14 uniform phases (46.3 ns each), and uses the phase information written for all 14 phases of each UI. When transmitting pulses, the CS61581 will add the amplitude information from the prior two symbols with the amplitude of the first UI of the current symbol before outputting a signal on TTIP/TRING.
24
DS-1 (50% duty cycle) Arbitrary Waveform Example DSX-1 (54% duty cycle) Arbitrary Waveform Example
Therefore, a mark preceded by two spaces will be output exactly as the mark is programmed. However, when one mark is preceded by marks, the first portion of the last mark may be modified. With AMI data, where successive pulses have opposite polarity, the undershoot tail of one pulse will cause the rising edge of the next mark to rise more quickly, as shown in Figure 14. The amplitude of each phase is described by a 7-bit, two's compliment number, where a positive value describes pulse amplitude, and a negative value describes pulse undershoot. The positive full value is 0x3F. The negative full value is 0x40. For T1, the typical output voltage is 38 mV/LSB. For E1 coax, the typical output voltage is 22 mV/LSB. For E1 shielded twisted pair, the typical output voltage is
E1 Arbitrary Waveform Example
Figure 13. Phase Definition of Arbitrary Waveforms
DS211PP8 DS211F1
CS61581
ory access in the sequence is a read instead of a write.
4.1
Power On Reset / Reset
Upon power-up, the IC is held in a static state until the supply crosses a threshold of approximately 3 Volts. When this threshold is crossed, the device will delay for about 10 ms to allow the power supply to reach operating voltage. After this delay, calibration of the transmit and receive sections commences. Because power up conditions can vary considerably, it is recommended that the device be reset after the power supply has stabilized to ensure a known initial operational condition. The internal frequency generators can be calibrated only if a reference clock is present. The reference clock for the transmitter is provided by TCLK. The reference for the receiver is either the crystal oscillator or MCLK. If both the oscillator and MCLK are active, MCLK will be used as the reference source. The initial calibration should take less than 20 ms after pulses are input to the receiver. In operation, the device is continuously calibrated, making the performance of the device independent of power supply or temperature variations. The continuous calibration function forgoes any requirement to reset the line interface when in operation. However, a reset function is available which will reinitiate calibration and clear all registers and clear the Network Loopback function. In Host Mode, a reset is initiated by simultaneously writing RLOOP and LLOOP to the register. The reset will set all registers to "0" and initiate a calibration. A reset will also set LOS high in the Short Haul configuration. In Hardware Mode, the CS61581 is reset by simultaneously setting RLOOP and LLOOP high for at least 200 ns. Hardware reset will clear Network Loopback functionality
Figure 14. Example of Summing of Waveforms
27 mV/LSB. All voltages are peak voltages across the TTIP and TRING outputs. On the secondary of a 1:2 step-up transformer, the mV/LSB is twice the values stated above. Note that although the full scale digital input is 3F, it is recommended that full scale output voltage on the transformer primary be limited to 2.4 V peak. At higher output voltages, the driver may not drive the requested output voltage. Writing the arbitrary waveform RAM requires a deviation from normal serial port access. Register 0x13 is the RAM address register for the arbitrary waveform. Two consecutive address bytes are written; first the Address/Command Byte is written to address 0x13, followed by the address in RAM to be written. This dual address is then followed by the data byte for the waveform amplitude. There are 42 RAM byte locations (numbered 0x00 to 0x29). Each phase amplitude is written as an eightbit byte, where the first phase of the symbol is written first. The amplitude bytes are written LSB first. Reading the Arbitrary Waveform RAM follows the same sequence as the write, except the third mem-
DS211PP8 DS211F1
25
CS61581
4.2 Power Supply
tantalum and 1.0F mylar or ceramic capacitor should be connected between TV+ and TGND, and a 0.1F mylar or ceramic capacitor should be connected between RV+ and RGND. Place capacitors as closely as possible to their respective power supply pins. Wire-wrap breadboarding of the line interface is not recommended because lead resistance and inductance serve to defeat the function of the decoupling capacitors.
The device operates from a single +5 Volt supply. Separate pins for transmit and receive supplies provide internal isolation. These pins should decoupled to their respective grounds. TV+ must not exceed RV+ by more than 0.3 V. Decoupling and filtering of the power supplies is crucial for the proper operation of the analog circuits in both the transmit and receive paths. A 47F
Availability (Note 25) Host Mode (Note 26) Diagnostic Mode H/W Host Maskable Loopback Modes Local Loopback (LLOOP) Yes Yes No Remote Loopback (RLOOP) Yes Yes No In-band Network Loopback (NLOOP) Yes Yes Yes Internal Data Pattern Generation and Detection Transmit All Ones (TAOS) Yes Yes No Quasi-Random Signal Source (QRSS) No Yes No In-band Loop-up/down Code Generator No Yes No Error Insertion and Detection Quasi-Random Signal Detection (QDET) No Yes No Quasi-Random Signal Error Insertion (INS_QERR) No Yes No Bipolar Violation Detection (BPV) Yes Yes No Alarm Condition Monitoring Receive Loss of Signal Monitoring (LOS) Yes Yes Yes Receive Alarm Indication Signal Monitoring (AIS) No Yes Yes Other Diagnostic Reports Receive Line Attenuation Indicator (LATN) Yes Yes No Notes: 25. In Hardware Mode the Diagnostic Modes are selected by directly setting the pins on the device; in Host Mode, the appropriate register bits are written for Diagnostic Modes. 26. In Host Mode the interrupts can be masked by writing a "1" to the LOS bit; there is no masking in the Hardware Mode. Table 5. Diagnostic Mode Availability
Turns ratio: Low Impedance Output/Hardware Mode Turns ratio: Matched Impedance Output Primary inductance Primary leakage inductance Secondary leakage inductance Interwinding capacitance ET-constant
1:2 step-up transmit, 1:1 receive 1:1.5 step-up transmit, 1:1 receive 1.2 mH min at 772 kHz 0.5 H max at 772 kHz with secondary shorted 0.5 H max at 772 kHz 40 pF max, primary to secondary 16 V-s min
Table 6. Transformer Specification
26
DS211PP8 DS211F1
CS61581
Turns Ratio(s) Manufacturer Pulse Engineering Valor Schott Valor Schott Pulse Engineering Valor Schott Valor Schott Pulse Engineering Schott Valor Schott Pulse Engineering Valor Pulse Engineering Pulse Engineering Valor Pulse Engineering Pulse Engineering Valor Pulse Engineering Pulse Engineering Part Number PE-64936 PT5008 67130840 ST5085 31187 PE-65351 PT5004 617130850 ST5086 31188 T-1054 31705 ST5074 31706 PE-68678 ST5162 PE-68877 T-1068 ST5173 T-1031 T-1022 ST5221 T-1077 T-1081 Package Type
1.5 kV, through-hole, single 1.5 kV, surface mount, single 1.5 kV, through-hole, single 1.5 kV, surface mount, single 1.5 kV, through-hole, single 1.5 kV, surface mount, single 1.5 kV, surface mount, dual 1.5 kV, surface mount, dual extended temp. 1.5 kV, surface mount, quad port 3 kV, surface mount, dual 1.5 kV, surface mount, dual 1.5 kV, surface mount, dual extended temp 3 kV, surface mount, dual
1:1CT
1:2CT
1:1.5CT
1:1CT 1:2CT
1:1CT 1:1.5CT
Table 7. Recommended Transformers for the CS61581
DS211PP8 DS211F1
27
CS61581
5. APPLICATIONS
+5V + 33 F RGND 28 Control & Monitor 1 12 6 18 11 RV+ 1 k. CLKE
MCLK
0.1 F 21 RV+ 15 TV+
+
1.0 F TGND
SCLK
CS
27 26 23 24 25 P Serial Port
LOS BPV LATN JASEL CS61581 IN HOST MODE
INT SDI SDO
5 MODE RPOS RNEG
RCLK
RTIP
19
R1
1 0.47 F 5
2 RECEIVE LINE 6
7 6 Frame Format Encoder/ Decoder 8 3 4 2 9 10
RRING
20
R2
TPOS TNEG TCLK XTALIN XTALOUT RGND 22 TGND 14 TRING TTIP 16 13 0.47 F
1CT:1 PE-64936 2 6 1:1.5 T-1054 1 TRANSMIT 5 LINE
T1 100 . R1 (. ) R2 (. ) 50 50
E1 75 . 37.5 37.5
E1 120 . 60 60
Figure 15. Matched Impedance Output Configuration
28
DS211PP8 DS211F1
CS61581
+5V + 33 F RGND 28 1 Control & Monitor 26 27 12 23 11 5 7 6 Frame Format Encoder/ Decoder 8 3 4 2 9 10 TAOS MCLK RLOOP LLOOP LOS NLOOP JASEL MODE RPOS RNEG RCLK TPOS TNEG TCLK XTALIN XTALOUT RGND 22 TGND 14 TRING TTIP 16 13 R4 R3 0.47 F CS61581 IN HARDWARE MODE RTIP 19 R1 20 R2 1 0.47 F 5 6 2 RECEIVE LINE 1CT:1 PE-64936 2 6 1:2 PE-65351 1 TRANSMIT 5 LINE LBO2 LBO1 24 25 Line Length Setting 0.1 F 21 RV+ 15 TV+ + 1.0 F TGND
RRING
T1 100 . R1 (. ) R2 (. ) R3 (. ) R4 (. ) 50 50 9.1 9.1
E1 75 . 37.5 37.5 9.1 9.1
E1 120 . 60 60 9.1 9.1
Figure 16. Low Impedance Output Configuration
DS211PP8 DS211F1
29
CS61581
+5V VSS TEST TMSYNC RMSYNC RFSYNC RSIGSEL RSIGFR RCHCLK RABCD TFSYNC TMO TSIGSEL TSIGFR TCHCLK TSER TABCD RSER VDD SPS TCLK TPOS TNEG RCLK RPOS RNEG TV+ RV+ MODE TCLK TPOS RCLK RPOS RNEG CLKE INT CS SCLK SDI SDO TTIP TRING Transmit Line
20 32 1 Signalling 28 27
40 19 3 12 13 24 34 35
Backplane Interface
1.544 MHz Serial Backplane
PCM Data
30 25 26 29 2 6 7 8 4 5 9 23 22 SLC-96 (R) multiframe sync 11 10
Control
CS62180B
PCM Data
INT CS SCLK SDI SDO RST RYEL RCL
14 17 18 15 16 33 21 36 37 38 39
RTIP RRING
CS61581
Receive Line
31
TNEG
Signalling
VDD
RLCLK RLINK TLCLK TLINK
RBV RFER
RLOS
D
PQ CQ
D
PQ CQ
RSIGSEL RMSYNC
(optional)
Data Link Supervision
Host Processor
Figure 17. Typical System Connection
30
DS211PP8 DS211F1
CS61581 CS61581
6. PI N DE SC R I PT I ON
MCLK TCLK TPOS/TDATA TNEG/UBS MODE RNEG/BPV RPOS/RDATA RCLK XTALIN XTALOUT JASEL LOS TTIP TGND
5 6 7 8 9 10 11 12 13 14 15 16 17 18 top view 4 3 2 1 28 27 26 25 24 23 22 21 20 19
TAOS/CLKE LLOOP/SCLK RLOOP/CS LBO2/SDO LBO1/SDI NLOOP/INT RGND RV+ RRING RTIP LATN NC TRING TV+
DS211F1 DS211P P8
31
CS61581
6.1 Power Supplies
Power supply for the transmit driver; typically +5 Volts.
TV+ - Power Supply, Transmit Driver, Pin 15. TGND - Ground Transmit Driver, Pin 14.
Power supply ground for the transmit driver; typically 0 Volts.
RV+ - Power Supply, Pin 21.
Power supply for all subcircuits except the transmit driver; typically +5 Volts.
RGND - Ground, Pin 22.
Power supply ground for all subcircuits except the transmit driver; typically 0 Volts.
6.2
Oscillator
A 6.176 MHz (or 8.192 MHz) crystal can be connected across these pins. This oscillator provides the reference frequency for the LIU if MCLK is not provided. The load capacitance presented to the crystal by these pins should be approximately 19 pF (IC and package, when soldered into a circuit board). The jitter attenuator may be disabled by tying XTALIN to RV+ through a 1 k. resistor, and floating XTALOUT. When XTALIN has no clock input, a clock must be supplied to the MCLK pin. Alternatively an external 6.176 MHz (8.192 MHz) clock can be driven into XTALIN, and the jitter attenuator circuit will operate. If MCLK is provided, and XTALIN is tied low or floated, the jitter attenuator will be enabled.
XTALIN, XTALOUT - Crystal Connections, Pins 9 and 10.
6.3
Control
Either MCLK or the crystal oscillator provide the master frequency reference for the CS61581. If both MCLK and the crystal oscillator are present, the oscillator is ignored. MCLK should be 1.544 MHz for T1 and 2.048 MHz) for E1. In a Loss of Signal state, RCLK will be derived from MCLK, through the jitter attenuator, if active. If MCLK is not provided, the jitter attenuator will hold the RCLK frequency in a Loss of Signal state. MCLK should be grounded if it is not used.
MCLK - Master Clock Input, Pin 1.
MODE - Mode Select Input, Pin 5.
Setting the MODE pin high puts the CS61581 into Host Mode where the device is controlled by a microprocessor, via a serial port. Setting the MODE pin low, configures the part for hardware mode control where various control and status are provided on dedicated pins. The MODE pin is internally pulled down placing the part in Hardware Mode when this pin is left floating. Tying the MODE pin to RCLK places the chip in Hardware Mode and enables the B8ZS encoder/decoder (provided that unipolar mode has been enabled; see the description for TNEG/UBS pin).
TAOS - Transmit All Ones Select Input, Pin 28 (Hardware Mode).
Setting TAOS to logic 1 causes continuous ones to be transmitted at the TCLK frequency. When TAOS is high, TPOS and TNEG (TDATA) are not output at the TTIP/TRING pins. TAOS is overridden by Remote Loopback. Setting TAOS, LLOOP, and RLOOP high simultaneously enables Network Loopback detection.
32
DS211F1 DS211PP8
CS61581
LLOOP - Local Loopback Input, Pin 27 (Hardware Mode).
Setting LLOOP to a logic 1 internally routes the transmitter input to the receiver output. If TAOS is low, the signal being output from the transmitter will be internally routed to the receiver inputs allowing nearly the entire chip to be tested. If TAOS and LLOOP are set high at the same time, the local loopback will occur at the jitter attenuator (excluding the transmit and receive circuitry) and the transmitter will transmit all ones. Simultaneously setting RLOOP and LLOOP high while TAOS is low resets the CS61581. Simultaneously setting RLOOP, LLOOP and TAOS high enables Network Loopback detection.
RLOOP - Remote Loopback Input, Pin 26 (Hardware Mode).
Setting RLOOP to a logic 1 causes the received signal to be passed through the jitter attenuator (if active) and retransmitted onto the line. The internal encoders/decoders will be bypassed in Remote Loopback. Simultaneously setting RLOOP and LLOOP high while TAOS is low resets the CS61581. Simultaneously setting RLOOP, LLOOP and TAOS high enables Network Loopback detection.
LBO1, LBO2 - Line Build Out 1 and 2, Pins 24 and 25 (Hardware Mode).
Transmitted line build out pulse shapes are selected by setting LBO[2:1] = 00 (0 dB), 01 (-7.5 dB), 10 (15 dB), or 11 (-22.5 dB).
JASEL - Jitter Attenuator Select, Pin 11.
If the jitter attenuator is enabled (crystal oscillator active, or XTALIN tied low or floated with MCLK provided), setting JASEL high places the jitter attenuator in the receive path; setting JASEL low places the jitter attenuator in the transmit path.
NC - No Connect, Pin 17.
The input voltage to this pin does not effect normal operation.
6.4
Status
LOS goes high when 175 consecutive zeros are received. LOS returns low when the ones density reaches 12.5% (based on 175 consecutive bit periods, starting with a one and containing less than 100 consecutive zeros, as prescribed in ANSI T1.231-1993 and ITU-T G.775). If LOS is true, and the jitter attenuator is in the receive path, RCLK will smoothly transition to MCLK if provided; RCLK will retain the frequency prior to LOS if MCLK is grounded. If the jitter attenuator is NOT in the receive path, RCLK will become the reference clock frequency (MCLK) if provided, or the crystal oscillator.
LOS - Loss Of Signal Output, Pin 12.
NLOOP - Network Loopback Output, Pin 23 (Hardware Mode).
NLOOP goes high when a 00001 pattern is received for five seconds putting the CS61581 into network (remote) loopback. NLOOP is deactivated upon receipt of a 001 pattern for five seconds, or by selection of LLOOP or RLOOP.
LATN - Line Attenuation Indication Output, Pin 18.
LATN is an encoded output that indicates the receive equalizer gain setting in relation to a five RCLK cycle period. If LATN is high for one RCLK cycle, the equalizer is set for 7.5 dB gain, two cycles = 15 dB gain, three cycles = 22.5 dB gain, four cycles = 0 dB. LATN may be sampled on the rising edge of RCLK.
6.5
Serial Control Interface
INT pulls low to flag the host processor when NLOOP, AIS or LOS changes state. INT is an open drain output and should be tied to the supply through a resistor.
INT - Interrupt Output, Pin 23 (Host Mode).
DS211F1 DS211PP8
33
CS61581
SDI - Serial Data Input, Pin 24 (Host Mode).
Data input to the on-chip register is sampled on the rising edge of SCLK.
SDO - Serial Data Output, Pin 25 (Host Mode).
Status and control information are output from the on-chip register on SDO. If CLKE is high, SDO is valid on the rising edge of SCLK. If CLKE is low, SDO is valid on the falling edge of SCLK. SDO goes to a high-impedance state when the serial port is being written to, or after bit D7 is output or CS goes high (whichever occurs first).
CS - Chip Select, Pin 26 (Host Mode).
The serial interface is accessible when CS transitions from high to low.
SCLK - Serial Clock Input, Pin 27 (Host Mode).
SCLK is used to write or read data bits to or from the serial port registers.
CLKE - Clock Edge, Pin 28 (Host Mode).
Setting CLKE to logic 1 causes RPOS and RNEG (RDATA) to be valid on the falling edge of RCLK, and SDO to be valid on the rising edge of SCLK. Conversely, setting CLKE to logic 0 causes RPOS and RNEG (RDATA) to be valid on the rising edge of RCLK and SDO to be valid on the falling edge of SCLK.
6.6
Data Input/Output
The 1.544 MHz (2.048 MHz) transmit clock is input on this pin. TPOS and TNEG or TDATA are sampled on the falling edge of TCLK.
TCLK - Transmit Clock Input, Pin 2.
TPOS/TNEG - Transmit Positive Pulse, Transmit Negative Pulse, Pins 3 and 4.
Data input to TPOS and TNEG is sampled on the falling edge of TCLK and transmitted onto the line at TTIP and TRING. An input on TPOS results in transmission of a positive pulse; an input on TNEG results in transmission of a negative pulse. If TNEG is held high for 16 TCLK cycles, the CS61581 reconfigures for unipolar (single pin NRZ) data at pins 3 and 7, TDATA and RDATA. If TNEG goes low the CS61581 switches back to two-pin bipolar data input format. The device should be reset when changing between unipolar and bipolar mode.
TDATA - Transmit Data, Pin 3.
When pin 4, TNEG/UBS, is held high, pin 3 becomes TDATA, a single-line NRZ (unipolar) data input sampled on the falling edge of TCLK.
UBS - Unipolar / Bipolar Select, Pin 4.
When UBS is held high for 16 consecutive TCLK cycles (15 consecutive bipolar violations) the CS61581 reconfigures for unipolar (single-line NRZ) data input / output format. Pin 3 becomes TDATA, pin 7 becomes RDATA, and pin 6 becomes BPV.
RCLK - Recovered Clock Output, Pin 8.
RCLK outputs the clock recovered from the input signal at RTIP and RRING. In a Loss of Signal state RCLK reverts to the MCLK frequency, or retains the frequency prior to the LOS state, depending on the clocks provided. See the LOS pin description.
RNEG/RPOS - Receive Negative Pulse, Receive Positive Pulse, Pins 6 and 7.
Recovered data output on RPOS and RNEG is stable and valid on the rising edge of RCLK in Hardware Mode. In Host Mode, CLKE determines the edge of RCLK on which RPOS and RNEG are valid. A positive pulse on RTIP with respect to RRING generates a logic 1 on RPOS; a positive pulse on RRING with respect to RTIP generates a logic 1 on RNEG. 34 DS211F1 DS211PP8
CS61581
RDATA - Received Data, Pin 7.
Unipolar data (single-line NRZ) data is output on RDATA when TNEG/UBS (pin 4), is held high. In Host Mode, CLKE determines the edge of RCLK on which RDATA is valid.
BPV - Bipolar Violation, Pin 6.
When pin 4 is held high, received bipolar violations are flagged by BPV (RNEG) going high along with the offending bit output from RDATA. If the B8ZS or HDB3 encoder/decoder is activated, BPV will not flag bipolar violations resulting from valid zero substitutions.
TTIP, TRING - Transmit Tip and Ring, Pins 13, 16.
The transmit signal to the line is sent out on these pins. They represent the signal driven on TCLK, TPOS, and TNEG (or TDATA).
RTIP, RRING - Receive Tip and Ring, Pins 19, 20.
The input pins for the receive signal from the line. They recovered clock and data driven on RCLK, RPOS, and RNEG (or RDATA).
DS211F1 DS211PP8
35
CS61581
28L PLCC PACKAGE DRAWING
e E1 E D2/E2
B
D1 D A
A1
DIM A A1 B D D1 D2 E E1 E2 e
MIN 0.165 0.090 0.013 0.485 0.450 0.390 0.485 0.450 0.390 0.040
INCHES NOM 0.1725 0.105 0.017 0.490 0.453 0.410 0.490 0.453 0.410 0.050
MAX 0.180 0.120 0.021 0.495 0.456 0.430 0.495 0.456 0.430 0.060 JEDEC # : MS-047
MIN 4.191 2.286 0.3302 12.319 11.430 9.906 12.319 11.430 9.906 1.016
MILLIMETERS NOM 4.3815 2.667 0.4318 12.446 11.506 10.414 12.446 11.506 10.414 1.270
MAX 4.572 3.048 0.533 12.573 11.582 10.922 12.573 11.582 10.922 1.524
36 DS211PP8
DS211F1 37
CS61581
Revision PP8 F1
Date April `00 Aug `05 Preliminary release.
Changes Removed 28-pin PDIP package option.
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find the one nearest to you go to www.cirrus.com
IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant infor mation to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPER TY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOM ER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks o service marks of their respective owners.
DS211F1
37

▲Up To Search▲

Price & Availability of CS61581

	To Download CS61581 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .